Heat is applied to the wire while heating, and cold-processing is used during cooling to shape a round cross section into an irregularly angled cross section.
This absorbs the phenomenon of the inner thickness increasing and the outer thickness decreasing, when a ring is formed (bent). Therefore, a uniform thickness is maintained after processing is completed.
Ring gears transmit the power of the starter motor to the crankshaft when the engine is started. Due to the addition of idle reduction functions in recent years, a greater level of durability and quality is required.
These parts are used primarily in manual transmission cars. They connect the engine to the clutch. Due to the vibration suppression applied in recent years, there has been an increase in dual mass flywheels with internal dampers.
These rings are installed on torque converters. They are machined with screw holes for installation on drive plates. These rings are installed on torque converters, in order to maintain the moment of inertia.
These products are installed on flywheels and drive plates. They are missing teeth in a specific location, which allows the rotation of the engine (crankshaft) to be detected.
These rings are used to maintain the strength of the housing. There is a notch along the shape of the housing on the inner diameter.
These parts are used in automatic transmission cars. They connect the engine to the torque converter. Ring gears are installed on the outer circumference.
Heat is applied to the wire while heating, and cold-processing is used during cooling to shape a round cross section into an irregularly angled cross section.
This absorbs the phenomenon of the inner thickness increasing and the outer thickness decreasing, when a ring is formed (bent). Therefore, a uniform thickness is maintained after processing is completed.
Ring gears transmit the power of the starter motor to the crankshaft when the engine is started. Due to the addition of idle reduction functions in recent years, a greater level of durability and quality is required.
These parts are used primarily in manual transmission cars. They connect the engine to the clutch. Due to the vibration suppression applied in recent years, there has been an increase in dual mass flywheels with internal dampers.
Heat is applied to the wire while heating, and cold-processing is used during cooling to shape a round cross section into an irregularly angled cross section.
This absorbs the phenomenon of the inner thickness increasing and the outer thickness decreasing, when a ring is formed (bent). Therefore, a uniform thickness is maintained after processing is completed.
Ring gears transmit the power of the starter motor to the crankshaft when the engine is started. Due to the addition of idle reduction functions in recent years, a greater level of durability and quality is required.
These parts are used primarily in manual transmission cars. They connect the engine to the clutch. Due to the vibration suppression applied in recent years, there has been an increase in dual mass flywheels with internal dampers.
Heat is applied to the wire while heating, and cold-processing is used during cooling to shape a round cross section into an irregularly angled cross section.
This absorbs the phenomenon of the inner thickness increasing and the outer thickness decreasing, when a ring is formed (bent). Therefore, a uniform thickness is maintained after processing is completed.
Ring gears transmit the power of the starter motor to the crankshaft when the engine is started. Due to the addition of idle reduction functions in recent years, a greater level of durability and quality is required.
Installation of a simple type of sensor on equipment enables you to visualize the presence/absence of operation and the production volume of each time period on the Internet.
This completely eliminates the burden on workers during data acquisition.
It can easily be installed on Showa equipment.
A wireless display box (operation, cycle stop, stop at N minutes or more, etc.) has been added to the basic type.
It can be installed at any location in the factory or office to visualizes the “right now” of the equipment.
You do not need a monitor, PC, or other OA equipment for display box installation.
A wireless stop-reason transmitter has been added to the basic type.
The ability to obtain information about any of nine different causes of equipment stoppage makes it ideal for investigating stoppages that are hindering productivity.
Additionally, this system prevents counts of adjustment and empty machining while the machine is stopped to ensure highly accurate production counts.
Analyzing the acquired data with dedicated software provides detailed visualization of daily operation status, as well as automatic calculations of hourly and performance utilization rates, hourly production volume, and similar items.
Comparing your results with standard values reveals waste and enables you to make efficient improvements.
Measures the current consumption of equipment by use of current sensors. The measured data can be visualized on the Internet to readily understand the current consumption of equipment in detail.
Carbon dioxide emissions are calculated from the measured data and the coefficient of your electric power company.
This system is essential for future production activities.
Operating status can be visualized by setting threshold values (operating/stopped) for the current data and processing it with dedicated software.
This can be used to improve productivity by extracting the operating status of parts with long cycle times and the idle time of your operating equipment.
The relationship between load (current) and time during machining can be calculated by reducing the current measurement cycle. Optimal machining conditions can be determined from the machining conditions and load (current) so that improvements such as increased tool life can be quantified to provide highly reliable improvements.
3-phase AC generator mainly used in automobiles.
Brackets, rotors, stators, and similar components are combined to produce fully-complete alternators. These alternators are delivered to automobile manufacturers after in-house performance tests, appearance inspections, and packaging.
Field coils for starters.
Wound flat wires are connected by fusing with connecting wire.
Brushes and terminal leads are also installed by fusing.
Gear cases used in starters.
Machining and metal press-fitting of die-cast products are used.
The yoke and magnetic switch parts are assembled together.
Contact case assemblies used in starters.
Part that is assembled together with the magnetic switch parts and receives electricity from the battery.
Retaining ring crimping for securing bolts, eyeleting for securing terminals, and similar features are produced by press-crimping using a crimping jig.
Stoppers used in starters.
They are assembled into the armature section.
Machined using a lathe with a bar feeder.
Motors used in the tilt mechanism of a truck cabin.
Power module cases used in inverters for battery electric vehicles. Flanges and cooling fins are joined by use of friction stir welding.
Parts used in continuously variable transmissions.
Racks for high-pressure fuel pump position control.
Coils assembled with a no-fuse circuit breaker.
We can provide bobbin winding, hollow winding, fusing, enamel removal, pre-soldering, and similar processes.